Mitsubishi Electric FREQROL Manuel d'instructions Page 192
- Page / 524
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Limit the output frequency Parameter
6 - 52
6.4.2 Avoid mechanical resonance points (frequency jumps) (Pr. 31 to Pr. 36)
When it is desired to avoid resonance attributable to the natural frequency of a mechanical sys-
tem, these parameters allow resonant frequencies to be jumped.
The above parameters can be set when Pr. 160 "User group read selection" = 0.
Up to three areas may be set, with the jump frequencies set to either the top or bottom point of
each area.
The settings of frequency jumps 1A, 2A, 3A are jump points, and operation is performed at these
frequencies in the jump areas.
Pr.
No.
Name Initial Value Setting Range Description Parameters referred to
Refer to
Section
31
Frequency jump 1A 9999 0–400Hz/9999
1A to 1B, 2A to 2B, 3A to 3B is
frequency jumps
9999: Function invalid
—
32
Frequency jump 1B 9999 0–400Hz/9999
33
Frequency jump 2A 9999 0–400Hz/9999
34
Frequency jump 2B 9999 0–400Hz/9999
35
Frequency jump 3A 9999 0–400Hz/9999
36
Frequency jump 3B 9999 0–400Hz/9999
Fig. 6-11:
Definition of the jump areas
I000019C
Hz
Pr.36 (3B)
Pr.35 (3A)
Pr.34 (2B)
Pr.33 (2A)
Pr.32 (1B)
Pr.31 (1A)
Set frequency
Output frequency
- FR-E720S EC 1
- FR-E740 EC 1
- Safety instructions 5
- Electric Shock Prevention 6
- Fire Prevention 7
- Injury Prevention 7
- Additional Instructions 8
- Contents 11
- 1.1 Inverter type 19
- 1.2 Description of the Case 20
- 1.2.1 Accessory 21
- 2 Installation 23
- I002051E 24
- Tighten the 25
- Example: FR-E740-230 25
- FR-E720S-008 to 030 26
- FR-E720S-050 to 110 26
- FR-E740-016 to 095 26
- 2.3 Mounting 27
- Mounting Installation 28
- 2.4 Enclosure design 29
- 2.4.2 Inverter placement 33
- Good example! 34
- Bad example! 34
- 3 Wiring 35
- 3.1.1 Peripheral devices 37
- Main circuit 38
- Control circuit 38
- 3.3 Main circuit connection 40
- FR-E740-230 and 300 41
- I001016E 45
- I001904E 46
- Current input 49
- (initial status) 49
- I001917E 51
- I001326E 51
- STF, etc 52
- 3.4.2 Wiring instructions 53
- AY40 Inverter 56
- AY80 Inverter 56
- 3.5 PU connector 57
- 3.5.2 RS-485 communication 58
- 3.6 USB connector 59
- I001922E 61
- I002036E 62
- Te r m i n a l + 62
- Te r m i n a l P R 62
- Brake resistor 63
- I002044E 66
- FFR-HEL-(H)-E 71
- 3.8.3 Power supply harmonics 79
- Wiring Length 80
- ≤ 50m 50m to 100m ≥ 100m 80
- 4 Operation 81
- Undesirable current 82
- I001877E 83
- I001878E 84
- I001879E 85
- 4.2 Drive the motor 86
- 4.3 Operation panel 87
- Operation Operation panel 89
- FR-E700 EC 4 - 9 89
- 4.3.4 Operation lock 92
- FR-E700 EC 4 - 13 93
- Fig. 4-9: Operation lock 93
- 4.3.6 First priority monitor 94
- 4.3.7 Digital dial push 94
- Operation panel Operation 98
- 5 Basic settings 99
- V/FV/FV/F 102
- I001098E 103
- I001100E 105
- Clamped at the 105
- I001747E 106
- PRM indication is lit 106
- PU indication is lit 106
- Pr. 7 Pr. 8 107
- Flickering 116
- 5.2 PU operation mode 118
- I001767E 119
- Flickers for about 5s 119
- 3s later 119
- I001768E 121
- I001769E 122
- I000004aC 122
- I001770E 123
- I001772E 124
- I001773E 126
- I001774E 127
- 5.3 External operation 128
- I0001086E 130
- FR-E700 EC 5 - 35 133
- I001094E 137
- 6 Parameter 141
- Parameter overview Parameter 144
- Parameter Parameter overview 145
- FR-E700 EC 6 - 5 145
- FR-E700 EC 6 - 7 147
- FR-E700 EC 6 - 9 149
- FR-E700 EC 6 - 11 151
- 200V/400V 154
- FR-E700 EC 6 - 15 155
- FR-E700 EC 6 - 19 159
- FR-E700 EC 6 - 21 161
- 6.2 Control mode 170
- Setting range Pr. 0, Pr. 46 174
- Output voltage 174
- Load torque 178
- I001883E 183
- I001120E 183
- Constant speed 183
- I001330E 185
- I001900E 186
- I001545C 186
- Pr. 22 = 150% 186
- Pr. 23 = 100% 186
- Pr. 66 = 50Hz 186
- I000019C 192
- Set frequency 193
- Output frequency 193
- 6.5 Set V/f pattern 194
- I001322C 196
- I001323C 196
- I001547E 197
- I001127E 200
- I001788E 201
- Fig. 6-21: 202
- I000006C 210
- I001929E 211
- I000008C 213
- Forward rotation OFF 214
- I000015C 215
- I000016C 216
- I000017C 216
- I001137C 223
- I001138E 224
- I000553C 224
- R1 l1 l2 236
- I000007C 239
- I001566E 242
- I001143E 243
- I001144E 244
- I001567E 245
- I001568E 246
- I001569E 246
- Mechanical 246
- I001793E 250
- I001571E 251
- I001572E 252
- Output shutoff signal 257
- I000011C 258
- I001145C 259
- I001794E 259
- Inverter 261
- Reverse 262
- Forward 262
- FR-E700 EC 6 - 123 263
- Start signal selection 263
- FR-E700 EC 6 - 125 265
- I001796E 267
- Starting frequency Pr. 13 267
- Reset processing 267
- I001797E 268
- I000020C 269
- I001798E 270
- I001155E 271
- I001156E 272
- I001799E 274
- I001158E 275
- I001800E 281
- I001801C 281
- I001164E 286
- I001165E 287
- I001931E 288
- I001168C 289
- I001932E 289
- 6.12.1 Automatic restart 291
- I001901E 293
- I000722C 294
- I001170E 296
- I001814E 302
- I001815E 303
- I001175E 303
- I001176E 304
- I001177E 304
- I001178E 307
- I001179E 307
- 6.14 Energy saving operation 311
- I001816E 313
- I001934E 315
- I001182E 317
- I001884E 317
- Voltage input 317
- I001191E 322
- I000027C 330
- I001823E 339
- Disabled 341
- I001205E 342
- I001825E 343
- I001826E 344
- I001827E 344
- No signal assignment 360
- 6.19.1 PU connector 361
- I001829E 362
- I001211E 362
- I001212E 362
- I001938E 364
- I001939E 364
- FR-E700 EC 6 - 227 367
- I000030C 374
- I000038C 377
- I000039C 378
- I002068E 388
- I001227E 393
- I001228E 394
- Tab. 6-92: Error check item 402
- ● Parameter 406
- Tab. 6-97: Parameter 406
- 343 (Read only) 1 0 408
- I001921E 409
- 6.20 Special operation 410
- Parameter Special operation 411
- FR-E700 EC 6 - 271 411
- I001231E 412
- I000045C 412
- I000046C 413
- I001233E 413
- I000047C 414
- I000048C 414
- I001838C 415
- I001234E 418
- I001237E 419
- Deviation 420
- Manipulated variable (Hz) 420
- I001841E 424
- I001842C 424
- I001894E 427
- I001843E 429
- I001627E 431
- I001260E 434
- 6.21 Useful functions 435
- I001262E 436
- I001261E 436
- I001263E 440
- I001940E 441
- I001266E 443
- I001267E 443
- I001844E 448
- 7 Troubleshooting 451
- 7.1 List of alarm display 452
- FR-E700 EC 7 - 3 453
- Error Message 454
- FR-E700 EC 7 - 5 455
- FR-E700 EC 7 - 9 459
- 7.4 LED display 467
- I001858E 469
- The parameter number 469
- 7.6.1 Motor does not start 470
- FR-E700 EC 7 - 21 471
- FR-E700 EC 7 - 23 473
- FR-E700 EC 7 - 25 475
- FR-E700 EC 7 - 27 477
- FR-E700 EC 7 - 29 479
- I001313E 480
- 7.7.1 Measurement of powers 481
- 7.7.3 Measurement of currents 482
- 8 Maintenance and inspection 485
- Parts Judgement Level 488
- I002039E 489
- 8.1.6 Cleaning 490
- 8.1.7 Replacement of parts 490
- I001860E, I001861E 491
- I001941E 491
- I001864E 492
- I001865E, I001866E 492
- I001942E 492
- AIR FLOW 492
- 8.1.8 Inverter replacement 494
- 8.2.2 Pressure test 495
- I002040E 496
- A Appendix 499
- A.1.2 3-phase, 400V class 500
- A.2 Common specifications 501
- A.3.1 FR-E720S-008 to 030 503
- A.3.2 FR-E720S-050 and 080 504
- FR-E700 EC A - 7 505
- A.3.4 FR-E740-120 and 170 506
- A.3.5 FR-E740-230 and 300 506
- A.3.6 Parameter unit FR-PU07 507
- A.3.7 Parameter unit FR-PA07 508
- FR-E700 EC A - 13 511
- FR-E700 EC A - 15 513
- FR-E700 EC A - 17 515
- FR-E700 EC A - 19 517
- MITSUBISHI ELECTRIC 524
Produits connexes et manuels pour Tournevis électriques Mitsubishi Electric FREQROL
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.899 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels