Mitsubishi-electric Mr. Slim PKA-A-GA Manuel d'utilisateur télécharger pdf (Page 11)

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

3 4

1 2

A Pair No. of wireless remote controller Indoor PC board

0 Factory setting

1 Cut J41

2 Cut J42

3–9 Cut J41, J42

4) Assigning a remote controller to each unit (Fig. 6-7)

Each unit can be operated only by the assigned remote controller.

Make sure each pair of an indoor unit PC board and a remote controller is assigned

to the same pair No.

5) Wireless remote controller pair number setting operation

1 Press the SET button with something sharp at the end.

Start this operation from the status of remote controller display turned off.

MODEL SELECT

blinks and Model No. is lighted.

2 Press the

min

button twice continuously.

Pair No. “0” blinks.

3 Press the temp

button to set the pair number you want to set.

4 Press the SET button with something sharp at the end.

Set pair number is lighted for three seconds then turned off.

Fig. 6-7

Fig. 6-8

CHECK

ON/OFF TEMP

FAN

VANE

TEST RUN

AUTO STOP

AUTO START

min

LOUVER

MODE

CHECK

RESETSET CLOCK

CHECK

C,D

Fig. 6-9

CHECK

6. Electrical work

? Mode number

? Setting number

? Refrigerant address

? Unit number

ON/OFF TEMP

FAN

VANE

TEST RUN

AUTO STOP

AUTO START

min

LOUVER

MODE

CHECK

RESETSET CLOCK

MODEL SELECT

1,4

6.3. Function settings

6.3.1 Function setting on the unit (Selecting the unit functions)

1) For wired remote controller (Fig. 6-8)

Changing the power voltage setting

• Be sure to change the power voltage setting depending on the voltage used.

1 Go to the function setting mode.

Switch OFF the remote controller.

Press the A and B buttons simultaneously and hold them for at least 2

seconds. FUNCTION will start to flash.

2 Use the C button to set the refrigerant address (3) to 00.

3 Press D and [--] will start to flash in the unit number (4) display.

4 Use the C button to set the unit number (4) to 00.

5 Press the E MODE button to designate the refrigerant address/unit number. [--]

will flash in the mode number (1) display momentarily.

6 Press the F buttons to set the mode number (1) to 04.

7 Press the G button and the current set setting number (2) will flash.

Use the F button to switch the setting number in response to the power supply

voltage to be used.

Power supply voltage

230 V : setting number = 1

208 V : setting number = 2

8 Press the MODE button E and mode and the setting number (1) and (2) will

change to being on constantly and the contents of the setting can be confirmed.

9 Press the FILTER A and TEST RUN B buttons simultaneously for at least two

seconds. The function selection screen will disappear momentarily and the air

conditioner OFF display will appear.

2) For wireless remote controller (Fig. 6-9)

Changing the power voltage setting

• Be sure to change the power voltage setting depending on the voltage used.

1 Go to the function select mode

Press the

CHECK

button F twice continuously.

(Start this operation from the status of remote controller display turned off.)

CHECK

is lighted and “00” blinks.

Press the temp

button C once to set “50”. Direct the wireless remote controller

toward the receiver of the indoor unit and press the

button A.

2 Setting the unit number

Press the temp

button C and D to set the unit number “00”. Direct the wireless

remote controller toward the receiver of the indoor unit and press the

min

button B.

3 Selecting a mode

Enter 04 to change the power voltage setting using the

C and D buttons.

Direct the wireless remote controller toward the receiver of the indoor unit and press

the

button A.

Current setting number: 1 = 1 beep (one second)

2 = 2 beeps (one second each)

3 = 3 beeps (one second each)

4 Selecting the setting number

Use the

C and D buttons to change the power voltage setting to 01 (240 V).

Direct the wireless remote controller toward the sensor of the indoor unit and press

the

button A.

5 To select multiple functions continuously

Repeat steps 3 and 4 to change multiple function settings continuously.

6 Complete function selection

Direct the wireless remote controller toward the sensor of the indoor unit and press

the

button E.

Note:

Whenever changes are made to the function settings after installation or main-

tenance, be sure to record the changes with a mark in the “Setting” column of

the Function table.

6.3.2 Function setting on the remote controller

Refer to the indoor unit operation manual.

BG79U874H01_en 05.11.30, 9:2411

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Mitsubishi-electric Mr. Slim PKA-A-GA Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Adoucisseurs Mitsubishi-electric Mr. Slim PKA-A-GA